160 manufacturers · 18,987 products

These Wall Washer lampholders feature a cylindrical scoop design that provides broad uniform illumination. Models support R30 and R40 or PAR38 lamps. They are certified for use with Halo and Lazer-by-Halo track and track systems.

With sleek simple lines, numerous beam distributions and color temperatures, and all-encompassing light output levels, Stasis gives the flexibility to create spaces that draw clout, foot traffic, sales and good reviews.

180° Motion sensor, solar powered high output LED motion activated light. Unique design can be used as a twin head or single head depending on application.

The HALO Outdoor LED Vapor Tight Floodlight provides an indoor/outdoor solution in applications where lighting fixture protection is required. The fixture provides equivalent light output to a 100-watt incandescent and 23-watt CFL fixture, with high-quality long lasting illumination. The fixture is vapor tight protecting against dust and moisture. This fixture’s traditional look and warm color temperature gives consumers the comfort of lighting they are used to. This fixture is ideal for patios, garages, storage, and industrial areas.

180° Motion sensor. Motion sensor turns lights ON automatically when motion is detected and OFF after a pre-selected time delay (4 or 12 minutes). Integral photo cell design prevents lights from turning ON with motion during daylight hours (auto modes). Power outage protection: saves energy by automatically resetting at dawn if lights are triggered by power interruption.

The OSC-P-1500 is a Passive Infrared (PIR) ceiling mount, 24VAC powered occupancy sensor that works in conjunction with Cooper Lighting Solution’s Power Packs to control lighting. The sensor’s main function is to turn the lights ON or maintain the lights ON while movement is detected within the sensor’s range and to turn the lights OFF when the space is left unoccupied. The sensor uses a dual element PIR heat detector that resides behind a multi-zone optical lens. This Fresnel lens establishes dozens of zones of detection. The sensor is sensitive to the heat emitted by the human body. In order to trigger the sensor, the source of heat must move from one zone of sensing to another. Non-moving hot objects will not cause the lights to turn ON (like incandescent lights).

The BAA-OSC-DT Dual Tech Occupancy Ceiling Sensor is a 15-28VDC powered motion and daylight sensor. The sensor combines Passive Infrared (PIR) and Ultrasonic (US) technologies to monitor a room for occupancy to deliver maximum energy savings and ensure the greatest sensitivity and coverage for tough applications without the threat of false triggers. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings.

0-10v dimming to phase dimming converter

The Passive Infrared Single Level Occupancy Sensing Wall Switch is a motion sensing lighting control and conventional wall switch all-in-one that is used to for energy savings and convenience. ONW-P-1001-MV is designed to detect motion from a heat-emitting source (such as a person entering a room) within its field-of-view and automatically switch lights ON. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application. The EcoMeter provides a visual indicator of energy usage, increasing end user awareness and reminding individuals to take control of their lighting to maximize energy savings.

The Room Controller Personal Remote is a handheld tool that provides the user the ability to individually control relays, dimmers and scenes. It also allows programmability of the individual scene buttons that can be packaged/configured to create Scene Wallstations. Each scene button can be programmed with user specified load ON/OFF and dimmer settings. Using the Room Controller Personal Remote (HHPR-RC) and daylight sensor (DSRC-FMOIR) the user can define up to six scenes and save them into the Room Controller to be recalled later from the Scene buttons or the Personal Remote.

The Distributed Low-Voltage Power System programming remote is a handheld IR device used to configure the DLVP system. The DLVP programming remote is a handheld tool that provides the user the ability to individually toggle zones, set sensor hold times and sensitivity, set daylight gains by zone, set sensor range, and assign fixtures with integrated sensors to control zones.

The Receptacle Rated Switchpack includes a 20A relay for ON/OFF control of connected outlets. The Receptacle Rated Switchpack connects to the Greengate Room Controller, DLVP power module, or any standard Greengate Occupancy Sensor. This powerpack provides energy-efficient control of receptacles.

The MicroSet Dual Technology Line Voltage Occupancy Sensing Ceiling Sensor is a motion sensing lighting control that is used for energy savings and convenience. MicroSet self-adjusting Dual Technology sensors drastically simplify and reduce a contractor’s installation and adjustment time period. The sensor is available in both single and dual load control.

The Passive Infrared Single Level Vacancy Sensing Wall Switch is a motion sensing lighting control and conventional wall switch all-in-one that is used to for energy savings and convenience. The VNW-P-1001-MV uses Passive Infrared (PIR) sensor technology to monitor a room for occupancy and deliver maximum energy savings. The lights are turned ON by pressing the universally recognized light icon pushbutton. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application.

The Ethernet Interface Module (EIM) provides secure serial-to-ethernet data transmission to enable data exchange between Keeper Enterprise, Greengate programming software application, and the Greengate panels. The device supports the SSL and SSH protocols, which work by encrypting data before sending it over the ethernet network.

The ONW-D Dual Technology RR7 Compatible Occupancy Sensing Wall Switch is a motion sensing lighting control that is used or energy savings and convenience. This low voltage unit interfaces directly with GE RR7 Relay Systems. The ONW-D-1001-RR7 combines Ultrasonic and Passive Infrared (PIR) sensor technologies to monitor a room for occupancy to deliver maximum energy savings and ensure the greatest sensitivity and coverage for tough applications without the threat of false triggers. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application. The EcoMeter provides a visual indicator of energy usage, increasing end user awareness and reminding individuals to take control of their lighting to maximize energy savings.

The (ONW-P-1001-RR7) Passive Infrared RR7 Compatible Occupancy Sensing Wall Switch is a motion sensing lighting control that is used for energy savings and convenience. This low voltage unit interfaces directly with GE RR7 Relay Systems. The ONW-P-1001-RR7 is designed to detect motion from a heat-emitting source (such as a person entering a room) within its field-of-view and automatically switch lights ON. These sensors have multi-segmented lenses. The sensor includes self adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application. The EcoMeter provides a visual indicator of energy usage, increasing end user awareness and reminding individuals to take control of their lighting to maximize energy savings. HVAC mode allows the load connected to the Form C BAS relay to remain ON when the lights are turned OFF manually.

The Distributed Low-Voltage Power System utilizes pre-terminated low-voltage lighting cables for safe, flexible LED lighting installations. Low-voltage lighting cables provide for fast, error free installation of LED light fixtures. Cables are available in pre-terminated lengths typical to application / fixture type for error free connectivity of Class 2 circuits in plenum rated applications.

The WBSD-010-CCT Slide Controller provides intuitive full-range classic linear-slide control of 0-10V compatible Correlated Color Temperature (CCT) capable light sources. These slider control units are ideal for commercial lighting applications and are compatible with decorator style devices and wall plates.

The 0-10V Decorator Dimmer provides full-range classic linear-slide dimming for 0-10 Volt compatible dimmable light sources. These units are ideal for light commercial applications and are compatible with decorator style devices and wallplates. Units feature a preset “ON/OFF” switch that automatically returns controlled light(s) to a preset level without disturbing the brightness level. The device is designed for both Single-pole (one location) and 3-way (multi-location) applications.

The Dual Technology Dual Relay Occupancy Sensing Wall Switch is a motion sensing lighting control and conventional wall switch all-in-one that is used for energy savings and convenience. The unit contains two relays that allow the control of two separate loads. The ONW-D-1001-DMV-N combines Ultrasonic (US) and Passive Infrared (PIR)sensor technologies to monitor a room for occupancy to deliver maximum energy savings and ensure the greatest sensitivity and coverage for tough applications without the threat of false triggers. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application. The EcoMeter provides a visual indicator of energy usage, increasing end user awareness and reminding individuals to take control of their lighting to maximize energy savings.

The Relay Interface Module is available in 120, 277 or 347 VAC input voltage configurations. The Relay Interface Module (RIM) is designed to force all relays in a lighting control panel to an ON or closed state regardless of the control panel programmed relay status. This allows the closure of relays during loss of normal (grid) power to allow an alternate power source to drive the lighting loads. Once the RIM senses the normal power returning, the control panel will return to the normal programmed operating mode. UL 924 Listed Accessory (ControlKeeper TouchScreen and LiteKeeper 16 & 32 panels).

Combining the functionality of a switchpack, a sensor, and a 0-10V dimmer, this convenient wallbox device saves labor costs and reduces installation times. What's more: it meets all the latest energy codes and standards, including Title 24. This model features both ultrasonic (US) and passive infrared (PIR) sensing technologies.

The OSW-P-0801-120 Passive Infrared Single or 3-way Occupancy Sensing Wall Switch is designed to detect motion from a heat-emitting source (such as a person entering a room) within its field-of-view and automatically switch lights ON. These sensors have multi-segmented lenses. For units to sense motion, the person must cross between two segments. The distance between segments increases the farther you are from the sensor, so motion has to be larger the farther you are from the unit. PIR sensors are considered line-of-sight sensors, meaning that the sensor must be able to have a direct line-of-sight to the person making the motion. In Automatic On Mode, the lights turn ON when a person enters the room. The sensor provides true multi-way ON/OFF control. When lights have been activated, the lights will remain ON as long as on the sensor(s) continue to detect motion. The occupant may manually turn OFF the lighting by pressing the ON/OFF button on any of the connected devices. If the room becomes vacant and the lights are ON, the lights will turn OFF when the unit that detected motion last times-out.

Available in both a network and stand-alone architecture, Room Controller offers code-compliant lighting, emergency, and plug load control out-of-the-box when connected to Room Controller low voltage devices. The system includes three relays and up to three 0-10 VDC dimming outputs to control compatible dimmable ballasts. Network up to 254 ControlKeeper and Room Controller Network panels.

Dual Relay Switchpacks provide 24 VDC operating voltage to all low voltage, 24 VDC, Greengate occupancy sensors and day lighting controllers. These powerpacks can be used where two circuits need to be controlled at the same point. A single switchpack can provide power for up to five sensors. Up to ten switchpacks can be connected to one sensor for control of multiple circuits. Isolated contacts may also be used to control HVAC, contactors, motors, etc.

The Dual Technology sensor’s combination of Ultrasonic and Passive Infrared technologies offers the most complete sensing equipment available today. This pairing helps eliminate false activations or deactivations for additional energy savings. The OAC-DT sensors are also equipped with MicroSet self-adjusting technology which provides an adaptive and airflow tolerant technology, making them ideal for spaces which have increased airflow due to higher occupant levels. MicroSet self-adjusting Dual Technology sensors drastically simplify and reduce a contractor’s installation and adjustment time period.

The Partitioning IR Transmitter and Receiver (IRTR) is a system accessory commonly used for the WaveLinx Wired Lighting Control System. It is used to sense the presence or absence of partitions such that lighting functions change to accommodate the appropriate size space. Requires connection to a UIG-2-NA.

The Multi-load Decorator Dimmer provides full-range classic linear-slide dimming for 300W dimmable LED and CFL as well as 600W Incandescent, Halogen, Dimmable Fluorescent, Electronic Low Voltage & Magnetic Low Voltage light sources. Preset units feature a preset “ON/OFF” switch that automatically returns controlled light(s) to a preset level without disturbing the brightness level. The device is designed for both Single-Pole (one location) and 3-Way (multi-location) applications, and features an adjustable Rapid-Start setting which provides additional power for a brief time period to ensure lamp start-up at low dim settings. Compatible with any decorator wallplate. Compatible with most dimmable LED and CFL lamps. Adjustable rapid start feature ensures lamp start-up even at low dim levels.

The Integrated Sensor programming remotes (ISHH-01 and ISHH-01) are handheld tools to adjust the light level of fixtures controlled by Cooper Lighting’s SVPD-series integrated sensors. The SVPD integrated sensors are standalone integrated sensors, i.e. each luminaire operates independently. The ISHH-01 allows users to turn adjust the light level of a fixture (on/off, raise and dim and preset light levels). It also allows the programmability of occupied and un-occupied scenes as well as the Energy Saver scene. The ISHH-02 only allows the user to control the luminaire light level only, i.e. turning the lights on/off, dim or raise the light level or set the light to one of the preset light levels.

The network cable is used to interconnect the Greengate network lighting control panels. The typical data transmission cabling is GG9841 which contains 24 AWG single twisted shielded pair. When adding panels in the middle of an existing network, GG9842 cabling allows daisy-chain integrity by providing two twisted pairs of 24 AWG and shielded wire, allowing for an out and return pair within the same cable. Non-plenum and plenum rated versions are available.

The TracKeeper™ current limiting panel for track lighting allows designers to easily meet energy codes. Limiting the branch circuit volt-ampere rating with the TracKeeper™ provides you with a fixed power consumption limit for your installation as opposed to calculated values based on watts per linear foot of track. Additionally, the use of high efficiency luminaries will often yield a lower watts/linear foot number than is specified in the code. Available in either 16 or 32 circuit panels.

The Isolated RS-485 Repeater is designed to allow the expansion of the network wire beyond the specified 4,000 feet limitation as well as the approximate 32-panel limitation. It provides the ability to amplify the network signal through an additional 4,000 feet of network wire as well as an additional 32 panels. It also allows the electrical isolation of one side of the network from another assisting in minimizing the potential for network disruptions from ground faults present on the lighting control low voltage wiring between network ports.

The Passive Infrared Low Voltage Occupancy Sensing Wall/Corner sensor is a motion sensing lighting control that is used for energy savings and convenience. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application. Manual On feature for use with 1 or 2 momentary switches controlling 1 or more Switchpacks.

Instead of pulling line-voltage to low-voltage transformers installed every few feet, bring line voltage to the DLVP power module and pull pre-terminated, low-voltage cable to every fixture, sensor, control, and receptacle control in a space. Available in 2 power levels (300 and 600W), UL924 listed, and pre-assembled, DLVP delivers out-of-the-box, “plug and play” code compliance.

Wallstations are pre-engraved low voltage switches that operate on 24 VDC power supplied by the Room Controller or DLVP power module. Each wallstation is designed to fit in a standard decorator opening and has two QuickConnect ports for local network connections to eliminate wiring errors.

The Lighting Relay Module is available in 347 VAC input voltage. The Lighting Relay Module (LRM) is designed to force all relays in a lighting control panel to an ON or Closed state regardless of the control panel programmed relay status. This allows the closure of relays during loss of normal (grid) power to allow an alternate power source to drive the lighting loads.

The Passive Infrared Dual Relay Occupancy Sensing Wall Switch is a motion sensing lighting control and conventional wall switch all-in-one that is used for energy savings and convenience. The unit contains two relays that allow the control of two separate loads. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application. The EcoMeter provides a visual indicator of energy usage, increasing end user awareness and reminding individuals to take control of their lighting to maximize energy savings.

The OEF-P PIR Fixture Mount High Bay/Low Bay Dimming Occupancy Sensor with Integrated Photocell and Two Interchangeable Lenses provides 1-10V control. The OEF-P is easy to program and set for desired 1-100% continuous dimming levels during daylighting. It is also engineered to meet and exceed all standards requirements of ASHRAE Standard 90.1 2010. Provides robust mechanical latching relay. Relay always returns to close after power loss event. UL listed for electronic ballast loads 120/277V.

The OSW-U-0721-MV is a self contained, energy saving, motion-sensing lighting control which replaces a conventional wall switch and utilizes ultrasonic technology to detect room motion. The sensor produces a low-intensity, inaudible sound to detect occupancy in a room. Changes in the sensor’s acoustic wave caused by motion, such as walking into a room, reaching for a telephone or swiveling in a chair, will cause the lights to turn ON. The sensor does not respond to audible sound. Wall switches are ideal for smaller spaces where you will not have obstructions of line-of-sight due to switch location, room orientation or furniture placement.

The Input/Output Device (OCC-RJ45) provides connection of any Greengate low voltage occupancy sensor, or other low voltage maintain closure, to the Room Controller or DLVP power module to define the occupancy state of the space. The OCC-RJ45 also can be used as an output to the HVAC system, third party systems or Switchpacks based upon room occupancy status.

The External Power Supply is a system accessory for the Greengate Lighting Control System. It is used to power user interfaces and other accessories when additional power is needed.

Pre-terminated Control Cable, couplers and splitters connect the Room Controller or DLVP power module and devices simplifying the Click & Go connection enabling automatic functionality upon power up. Cables are pre-terminated with industry standard RJ45 connectors.

The screwless wallplate is a system accessory for Greengate wall box devices. The wallplate fits a standard decorator opening or toggle opening and provides a contemporary, sleek design. Screwless wallplates appear to float freely on the surface of the wall and are designed for easy and fast installation. Mounting plate attaches to the device and the wallplate is simply pressed into place.

The OSW-P-1001-MV Passive Infrared Single Level Occupancy Sensing Wall Switch is a motion sensing lighting control and conventional Wall Switch all-in-one that is used to for energy savings and convenience. PIR sensors are considered line-of-sight sensors, meaning that the sensor must be able to have a direct line-of-sight to the person making the motion. In Automatic On Mode, the lights turn ON when a person enters the room. In Manual On Mode, the lights are turned ON by pressing the Pushbutton. The sensor provides true multi-way ON/OFF control. When lights have been activated, the lights will remain on as long as one of the sensor(s) continue to detect motion. The occupant may manually turn OFF the lighting by pressing the ON/OFF button on any of the connected devices. If the room becomes vacant and the lights are ON, the lights will turn OFF when the unit that detected motion last times-out. Works with Incandescent, LED, Fluorescent, CFL, MLV, ELV or 1/2 HP motor load.

The DSRC-FMOIR is an open loop daylight sensor that measures the natural light contribution in order to automatically adjust the lighting zones. It is part of the Room Controller and DLVP system and provides three easily distinguished light levels, Low (3-300 lux), High (30-3000 lux), and Direct Sun (300-30000 lux). The high light sensor range is selected by default, although this can be adjusted using the IR handheld programmer.

The 37 pin receptacle kit is used with the Greengate Patient Control Station to provide an interface to the Greengate Lighting control panel, Nurse Call System and the entertainment System. The 37 Pin receptacle kit includes: Three pigtails, Stainless steel wall plate, Receptacle/dummy plug, Class 2 low voltage wiring.

The 0-10 Volt Slide Dimmer provides full-range classic linear-slide dimming for 0-10V compatible dimmable light sources. These units are ideal for light commercial applications and are compatible with decorator style devices and wallplates. The preset “ON/OFF” switch automatically returns controlled light(s) to a preset level without disturbing the brightness level. The device is designed for both Single-pole (one location) and 3-way (multi-location) applications.

The Dual Technology Low Voltage Occupancy Sensing Wall Switch is a motion sensing lighting control that is used for energy savings and convenience and utilizes an isolated form-C relay that integrates directly with lighting control, building, and HVAC systems. The ONW-D-1001-SP combines Ultrasonic and Passive Infrared (PIR) sensor technologies to monitor a room for occupancy to deliver maximum energy savings and ensure the greatest sensitivity and coverage for tough applications without the threat of false triggers. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application. The EcoMeter provides a visual indicator of energy usage, increasing end user awareness and reminding individuals to take control of their lighting to maximize energy savings. HVAC mode allows the load connected to the Form C BAS relay to remain ON when the lights are turned OFF manually.

The Dual Technology Single Level Occupancy Sensing Wall Switch is a motion sensing lighting control and conventional wall switch all-in-one that is used to for energy savings and convenience. The ONW-D-1001-MV-N combines Ultrasonic and Passive Infrared (PIR) sensor technologies to monitor a room for occupancy to deliver maximum energy savings and ensure the greatest sensitivity and coverage for tough applications without the threat of false triggers. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application. The EcoMeter provides a visual indicator of energy usage, increasing end user awareness and reminding individuals to take control of their lighting to maximize energy savings.

The Room Controller Wallstation Coupler is used when a primary wallstation is needed to control multiple room controller or DLVP units. When the Wallstation Coupler is connected to multiple wallstations, the primary wallstation will override any scene currently selected by any connected wallstation.

Listed for emergency lighting control applications, the RRU-X-UNV can simultaneously bypass both a line voltage switch and a 0-10V dimming signal, ensuring that emergency fixtures illuminate at full brightness during utility power interruptions. Its small size makes it ideal for junction box or integrated fixture mounting in wireless or other modern control systems. An integral test switch allows for quick testing and verification.

Combining the functionality of a switchpack, a sensor, and a 0-10V dimmer, this convenient wallbox device saves labor costs and reduces installation times. What's more: it meets all the latest energy codes and standards, including Title 24.

The passive infrared Extreme Temperature Sensor provides consistent, stable coverage where extreme heat, cold or humidity must be accommodated, and where there are wide fluctuations in temperature. Temperature compensating circuitry stabilizes sensitivity at temperatures –40°F to 125°F (-40°C to 52°C). Ambient light control circuit to avoid False ON/OFF from brief changes in background light. Lighting sweep function with selectable DIP Switch prevents unnecessary “lights ON” following power sweeps in facilities with computer control systems

The MicroSet Ultrasonic Low Voltage Occupancy Sensing Ceiling Sensor is a motion sensing lighting control that is used for energy savings and convenience. The ultrasonic sensor uses the Doppler principle. It produces a low intensity, inaudible sound and detects changes in sound waves caused by motion, such as walking into the room, reaching for the telephone, or turning in a chair. They are volumetric in nature and therefore not line-of-sight dependent. Since they fill the space with these sound waves, they are excellent in bathrooms with stalls, enclosed hallways, or other oddly shaped rooms. In addition, they are much more sensitive to smaller motions. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and Time Delay in real-time, maximizing the potential energy savings that are available in the particular application.

The Analog Photosensor is a system accessory for Greengate lighting control systems. It allows control of lighting levels based on how much natural light is present. Photosensors use a lens to gather light energy and provide an electrical signal to a controller device that is proportional to the measured light level. The sensor sensitivity is fixed, and based upon the sensor range selected. Available in indoor, outdoor, atrium, and skylight configurations.

The Dual Technology sensor’s combination of Ultrasonic and Passive Infrared technologies offers the most complete sensing equipment available today. This pairing helps eliminate false activations or deactivations for additional energy savings. The OMC-DT sensors are also equipped with MicroSet self-adjusting technology which provides an adaptive and airflow tolerant technology, making them ideal for spaces which have increased airflow due to higher occupant levels. MicroSet self-adjusting Dual Technology sensors drastically simplify and reduce a contractor’s installation and adjustment time period. Available as Buy American compliant.

The Greengate Patient Control Station provides the hospital patient or nursing home resident easy control over their lighting controls and shades with the added security of a standard connection to the Nurse Call system and the comfort of a universal TV controller. The patient control station provides large clearly labeled buttons in a fully sealed case.

The Dual Technology Dual Relay Occupancy Sensing Wall Switch is a motion sensing lighting control and conventional wall switch all-in-one that is used for energy savings and convenience. The unit contains two relays that allow the control of two separate loads. It does not require a neutral wire for installation making it ideal for retrofit applications. The ONW-D-1001-DMV combines Ultrasonic (US) and Passive Infrared (PIR)sensor technologies to monitor a room for occupancy to deliver maximum energy savings and ensure the greatest sensitivity and coverage for tough applications without the threat of false triggers. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application.

The Dual Technology sensor’s combination of Ultrasonic and Passive Infrared technologies offers the most complete sensing equipment available today. This pairing helps eliminate false activations or deactivations for additional energy savings. The OAWC-DT sensors are also equipped with MicroSet self-adjusting technology which provides an adaptive and airflow tolerant technology, making them ideal for spaces which have increased airflow due to higher occupant levels. Self-adjusting Dual Technology sensors drastically simplify and reduce a contractor’s installation and adjustment time period. Manual On feature for use with 1 or 2 momentary switches controlling 1 or more Switchpacks.