160 manufacturers · 18,987 products

The Intelligent Lighting Controls line voltage wall switch & 0-10 volt dimmer provides a stylish solution for spaces where manual dimming control is required. Designed with contractors in mind, the unit is significantly shallower than typical dimmers, resulting in less crowded wall boxes. Additionally, versatile wiring enables usage with or without a neutral connection. For dimming adjustment, intuitive raise and lower buttons are present in addition to the on/off button. Five vertically stacked LEDs are provided to indicate the current dimming level. Configurable dimming parameters include High/Low Trims, Turn on Levels, and Curve Types. This dimmer also matches the ILC family of wall switch occupancy sensors and 0-10V dimming wall switch sensors.

2R seriesrelays are designed to be the longest lasting, most reliable relays available. By incorporating a unique single moving contact, both endurance and reliability are significantly enhanced. These relays have been tested to handle 200,000 full load cycles and 1,000,000 no load cycles. They have two high quality nickel-silver contactsthat can handle today’s high-inrush loads. Relays are available with or without status contacts and are available with variousinterface connectors.

The ILC TR relay provides a unique solution for remote control and panel mount control applications. Because each relay hasits own internal powersupply, it can be mounted virtually anywhere without additional transformers or powersupplies. By incorporating a unique single moving dual contact design, both endurance and reliability are significantly enhanced. TR relays are magnetically latched, requiring only a momentary rectified pulse to open or close the contacts. Isolated pilot contacts are available for indication of relay status at the switch stations. Available TR-Retro relays automatically turn on upon power-up and require a momentary closure to turn the relay on and off.

The ILC Remote 20 (R20) and Remote 20 Dimming (R20D) relays are designed to be mounted at the power junction box or lighting fixture for direct control of the lighting load. Relays are controlled from the EVO panel using a standard CAT-5 cable connection to the R20 relay RJ-45 jack. The R20 series relay uses oversized contacts designed to handle LED inrush current. Tested at 16 Amps electronic driver that can commonly exceed 200% of running current of the R20D latching relay load. The R20D has galvanically isolated 0-10V dimming which allows for class 1 wiring of the low voltage dimming. Loss of power to the LLEVO panel will force dimmer output level to 100%.

The EVO Lite power pack operates one load of lighting or plug load. This power pack includes 12 configuration options, an on-board relay, and 0-10V dimming, integrated into one package for easy installation. The EVO Lite power pack is ideal for small offices or classrooms, made to meet energy code with daylight harvesting, plug load control, occupancy sensing, and vacancy sensing options. It has two RJ-45 ports: one to wire to switches and additional power packs, and another for sensors and additional power packs. This convenient and easy to install power pack can be used as a single device or combined with other EVO Lite power packs, for multi zone operation.

The LightLEEDer Emergency UL 924 bypass relay control panel will force relay's ON during a normal power outage. This panel has all the same features and functions as a standard LightLEEDer lighting controller, allowing normal control of relays with emergency bypass during a normal power failure event. Relays can be all EM or a combination of normal and EM. Each output has a jumper for selecting Force On, Force Off or No change, this allows for emergency on, load shedding off, or no control selection for each relay. Provided With Phase monitoring module and high voltage dividers. This LightLEEDer Emergency lighting panel is easy to install, no external devices or complicated wiring configurations needed, reducing material and installation costs.

Intelligent Lighting Controls wireless power pack controllers switch on/off power to a connected lighting load as directed by wirelessly linked sensors, photocells, and wall controls. Additionally, the unit’s 0-10V dimming option greatly simplifies applications where dimming control from multiple switch locations is required. For applications where a hybrid wireless/wired architecture is desired, this wireless power pack can also be ordered with auxiliary low voltage connections.

The LightSync EVO Room Controller is a distributed lighting panel that simplifies expansion of a LLEVO or any LightLEEDer panel. The LSEVO-RC supports up to four R20D relays, two photo sensors, and two 6-button G3 switches. Easily connect R20D relays with CAT-5 to control lighting loads, 0-10V dimming, or receptacles. Programming can be easily modified using the ILC Pro Bluetooth app or LightLEEDer Pro software.

Momentary Switch Stations are available from ILC in a Decora or toggle style form. These heavy duty switches have a momentary On/Off with a neutral center position. The switches are manufactured by Leviton®, Hubbell®, or Pass & Seymour® and acceptstandard switch plates. Switches can be wired to signal an input to control a relay(s), group(s), or preset(s) in any of ILC’s panels.

The LightLEEDer programmable lighting control relay panel is the key to a powerful, dependable, flexible and energy efficient lighting system. LightLEEDer panels come with our new Reliant40 relays which feature a superior four contact design—the first true 40Amp lighting relay. Reliant40 relays come in 1-, 2- and 3-pole configurations in a robust breaker-style body. LightLEEDer panels range in size from 4 to 64 relay capacity and are equipped with CAT-5 RJ45 connectors for LightSync data line devices and interconnecting panels. Panels include a keyboard and LCD screen, along with USB and TCP/IP connections for easy programming with our free LightLEEDer Pro Software. Add-on modules are available for connecting to BAS, theatrical, or security systems.

The ILC Remote 20 Amp, Emergency Bypass Relay combines normal relay operation with a UL 924 bypass relay in one convenient package. Relays are available in both a wired (R20D-EM) and wireless (WR20D-EM) version that uses the 915MHz radio frequency for communication to ILC wireless devices. When normal power is lost the EM relay will automatically force ON the EM load and send dimming to 100%. When normal power is restored the device will return to normal control. The R20D-EM and WR20D-EM have a relay test button, and a wired input that can be used for a remote test switch or as an override connection from a fire alarm system.

The LightLEEDer EVO Integrated 2 Relay Controller can operate up to two loads. This Controller includes the configuration options of an EVO with two on-board relays and 0-10V dimming integrated into one package for easy installation. The LLEVO-INT-2 relay Controller is ideal for a small office with two zones of lighting control with daylight harvesting or one lighting zone and a plug load. It has RJ-45 ports for local digital LightSync switches, occupancy sensors, and a photo sensor. This convenient and easy to install two relay Controller can be used as a stand-alone device or networked with other LightLEEDer panels.

The LightSync Occupancy Sensor 8 Input module is designed to power and receive signals from multiple sensors on each of its 8 independent inputs. Eliminate expensive power packs by simply direct- wiring the sensors into the inputs. This module mounts remotely in a location central to the sensors. Each independent input can control any relay(s), group(s), or preset(s) throughout the network.

The LightSync EVO Integrated 2 Room Controller has 2 isolated relays with 0-10V dimming. This controller integrates the control options of an EVO-RC with two on-board relays in one package for easy installation. Up to 3 LSEVO-INT-2-RC room cantrollers can be added to a LLEVO-INT-2 to extend its control into additional rooms or a small office with two zones of lighting control with daylight harvesting or one lighting zone and a plug load. It has RJ-45 ports for local digital LightSync switches, occupancy sensors, and a photo sensor. This convenient and easy to install two relay room controller is great for extending the controls of an LLEVO-INT-2 controller.

The Boca Lighting and Controls SMART Dimmer DMX provides an interface with a DMX512 dimming protocol and uses Micro-Step technology for high-resolution dimming.

The Boca Lighting and Controls NanoRouter-X provides a DMX interface to 4 independent DMX or analog fixture streams on the network.

Remote 120V 300W Class II Magnetic Transformer. Up to 6x50W connections, dimmable with any incandescent dimmer. 15′ wire max. each.

PIR. Outdoor 360° Ceiling Mount Sensor. The STEINEL IS 360 occupancy sensor is rain tight for safe reliable operation indoors and out. The sensors are passive infrared and respond to heat radiated from moving persons or other heat-emitting objects (such as vehicles). They automatically turn lights on when presence is detected and off when a space is left vacant. For unmatched coverage, the IS 360 incorporates three highly sensitive pyroelectric sensors that provide reliable, uninterrupted 360 coverage.

PIR. Outdoor 240° Wall Mount Sensors. The STEINEL IS 240-120 occupancy sensor is intended for vertical mounting to any 1/2” threaded cover plate or knockout and is rain tight for safe reliable operation indoors and out. The sensors are passive infrared and respond to heat radiated from moving persons or other heat-emitting objects (such as vehicles). They automatically turn lights on when presence is detected and off when a space is left vacant.

PIR. Outdoor 240° Wall Mount Sensors. The STEINEL IS 240-120 occupancy sensor is intended for vertical mounting to any 1/2” threaded cover plate or knockout and is rain tight for safe reliable operation indoors and out. The sensors are passive infrared and respond to heat radiated from moving persons or other heat-emitting objects (such as vehicles). They automatically turn lights on when presence is detected and off when a space is left vacant.

PIR. Outdoor 360° Ceiling Mount Sensor. The STEINEL IS 360 occupancy sensor is rain tight for safe reliable operation indoors and out. The sensors are passive infrared and respond to heat radiated from moving persons or other heat-emitting objects (such as vehicles). They automatically turn lights on when presence is detected and off when a space is left vacant. For unmatched coverage, the IS 360 incorporates three highly sensitive pyroelectric sensors that provide reliable, uninterrupted 360 coverage.

SENSORWORX wireless power pack controllers switch on/off power to a connected lighting load as directed by wirelessly linked sensors and wall controls. Additionally, the unit’s 0-10V dimming option greatly simplifies applications where dimming control from multiple switch locations is required. For applications where a hybrid wireless/wired architecture is desired, this wireless power pack can also be ordered with auxiliary low voltage connections. The SENSORWORX wireless power pack is rated to switch fully loaded circuits and utilizes a powerful microprocessor to optimize its switching timing, ensuring long relay life even when controlling high-inrush LED lighting. As with all SENSORWORX products, these power packs are easy to install and incorporate features which reduce contractor labor time. An elongated chase nipple with snaps for quick installation and an optional snap-on low voltage wire chamber make for a hassle free contractor experience. All SENSORWORX products are proudly made in the USA.

SENSORWORX line voltage photocell and daylight harvesting sensors provide a compact control solution without requiring a powerpack. Basic on/off units are capable of directly switching lights off when ambient levels are high enough that desired overall light levels will be still be maintained. Lights will be switched back on once ambient level falls below the desired setpoint. Units with the daylight harvesting (dimming) option track a space’s overall illumination and dim connected lighting to achieve energy savings. During times of high daylight contribution to a space, controlled artificial lighting will be gradually dimmed to a minimum dimmed level. During times of no or low daylight contribution, controlled artificial lighting will increase back up to its maximum level. The sensor can also be configured to switch lighting off completely in maintained high daylight conditions. Additional configurable parameters include high & low trim levels and fade rates. All photocells provide the option of selecting the ambient light threshold (e.g., setpoint) from a range of preset values or running an auto-selection mode where the unit will determine the setpoint based on the measured amount of light it is controlling.

The SENSORWORX line voltage wall switch & 0-10 volt dimmer provides a stylish solution for spaces where manual dimming control is required. Designed with contractors in mind, the unit is significantly shallower than typical dimmers, resulting in less crowded wall boxes. Additionally, versatile wiring enables usage with or without a neutral connection. For dimming adjustment, intuitive raise and lower buttons are present in addition to the on/off button. Five vertically stacked LEDs are provided to indicate the current dimming level. Configurable dimming parameters include High/Low Trims, Turn on Levels, and Curve Types. This dimmer also matches the SENSORWORX family of wall switch occupancy sensors and 0-10V dimming wall switch sensors.

​The SENSORWORX wireless wall switch load controller links to remote occupancy sensors and switches without low voltage wiring in order to provide automatic lighting control. Designed with contractors in mind, the unit is significantly shallower than typical dimmers, resulting in less crowded wall boxes. Additionally, versatile wiring enables usage with or without a neutral connection and never requires a minimum load. This switch also matches the SENSORWORX family of wall switch occupancy sensors and 0-10V dimming wall switch sensors.

The SENSORWORX family of line voltage ceiling mount occupancy sensors provides a compact control solution capable of switching lighting loads without requiring a powerpack. SENSORWORX products utilize the latest passive infrared technology and digital signal processing techniques to provide unmatched detection performance. Additionally SENSORWORX units are available with an integrated microphone to provide overlapping passive acoustic occupancy detection for rooms with obstructions.

The SENSORWORX family of wall switch occupancy/vacancy sensors provides a simple yet cost-effective lighting control solution for many retrofit applications. Designed with contractors in mind, the SENSORWORX 0-10V dimming wall switch sensor is significantly shallower than typical dimmers and sensors, resulting in less crowed wall boxes. Additionally, versatile wiring enables usage with or without a neutral and allows reversal of line and load connections. SENSORWORX products utilize the latest passive infrared technology and digital signal processing techniques to provide unmatched motion detection performance. These units are also available with an integrated microphone to provide overlapping passive acoustic occupancy detection for rooms with obstructions or where occupant motion is limited. For dimming adjustment, intuitive raise and lower buttons are present in a addition to an on/off button.

SENSORWORX power packs transform incoming line voltage power to low voltage as needed by sensors or other control devices. Additionally, they switch on/off power to the connected lighting load as directed by the sensors and controls. SENSORWORX power packs utilize a powerful microprocessor to optimize its switching timing in order to ensure long relay life even when controlling high-inrush LEDs and ballast loads. As with all SENSORWORX products, these power packs are easy to install and incorporate features which reduce contractor labor time. An elongated chase nipple and an optional snap-on low voltage wire chamber make for a hassle free contractor experience. All SENSORWORX products are proudly made in the USA.

The SENSORWORX family of wall switch occupancy sensors provides a simple yet cost-effective lighting control solution for many retrofit applications. Designed with contractors in mind, the SENSORWORX wall switch sensor is significantly shallower than typical sensors, resulting in less crowded wall boxes. Additionally, versatile wiring enables usage with or without a neutral and allows reversal of line and load connections. SENSORWORX products utilize the latest passive infrared technology and digital signal processing techniques to provide unmatched motion detection performance. These units are also available with an integrated microphone to provide overlapping passive acoustic occupancy detection for rooms with obstructions or where occupant motion is limited.

Easily adjustable compact digital ceiling sensor that excels due to its ability to utilize an industry leading mobile app to provision and troubleshoot. The mobile app allows contractors and technicians cut onsite time through an intuitive interface that provides active sensor feedback and provisioning flexibility. The device’s slim form factor provides a sleek aesthetic that blend into the ceiling maintaining the spaces visually appeal.

The WaveLinx LITE Contact Closure Input is a WaveLinx LITE device that provides the ability to take inputs from other devices, like fire alarm panels, keyed switches, or other devices, incorporating momentary or maintain actions to allow the system to respond to demand response, alert mode, after hours occupancy or a sensor input.

The PRO Wallstation (W-Series) is a multi-scene, single area dimming wallstation which provides customized light level for each area. The wallstation provides default sequence of operations including 50% light level, scene light levels between 30-70% as well as 100% and full off. Many wallstation configurations also include scene raise/lower buttons to further adjust the light levels.

The WaveLinx Wired Occupancy Ceiling Sensor - Multi Sensor (OCS-D-P06 / OCS-D-P12) combines daylight sensing and occupancy detection into a single device. The Multi-Sensor communicates over the two wire communication bus and allows for all device settings and groups to be adjusted remotely.

As part of the WaveLinx System, the PRO Wireless Receptacle (WR-15/WR-20) enables energy savings by turning OFF the top outlet when the area is unoccupied. The wireless receptacle is automatically paired with all WaveLinx occupancy sensors in a space when it is assigned to an area using the Wavelinx Mobile application. The wireless receptacle uses standard AC power wiring and has an internal relay that will Open/Close the controlled outlet. The use of wireless control features of WaveLinx reduces the wiring needed during installation. Use of the wireless control features of the receptacle also includes power measurement capabilities that can be displayed in the WaveLinx Mobile application.

CORE Locate delivers real-time indoor location service and management by leveraging the CORE smart space IoT platform. It's designed to let you monitor activities by sensing the location of your assets, so staff and patients can use the data to make improvements. Among them: optimized business/production workflows, enhanced safety and heightened security.

CORE Public REST API (TRX-API) provides a secure programming interface that enables third-party partners to obtain real-time data from WaveLinx controlled spaces as well as Cooper Lighting Solutions BLE tags. Partners can then use the data to offer value-added solutions that improve business processes and tenant experiences. The CORE Public API interface is hosted on the CORE Core appliances.

The WaveLinx Wired Forward Phase to ELV Power Extender (PE400-1) allows a dimmers power handling capacity to be extended to a full 1000W/VA on 120V input power. It allows a dimmer to dim or switch a fully loaded circuit of electronic low voltage and incandescent loads only.

The WaveLinx Wired Field Relay (FRS-DA) provides On/Off control and network connectivity in order to conserve energy and effectively manage the lighting system. The Field Relay uses advanced switching technology specifically designed to handle the large inrush currents and inductive loads found in lighting applications.

CORE Locate delivers real-time indoor location service and management by leveraging the CORE smart space IoT platform. It's designed to let you monitor activities by sensing the location of your assets, so staff and patients can use the data to make improvements. Among them: optimized business/production workflows, enhanced safety and heightened security.

The DMX light controller Output Interface (SCD96-NA) can control virtually any standard DMX device such as RGB fixtures, moving lights, dimmers, and effects. This unit provides DMX output that tracks 96 channels in the WaveLinx Wired system. These allow lighting sources that use DMX as the control signal to be used as part of the WaveLinx Wired system. This compact unit can be mounted virtually anywhere.

The WaveLinx Wired Digital Wallstation (FDW) offers the specification grade range of wallstations, which combines the easiest user interface in the industry with a large circular On/Off button, a universal module with up to 10 button configurations, large or small button options and engraving. Designed to fit with standard decorator wallplates, Wallstations can be ganged together to meet specific project needs. Individual buttons have backlight indicator lights and strong tactile feedback.

The CLS Wallstation is the new standard in intuitive layout and operation with a large circular On/Off button, an universal module with up to 10 button configurations and custom engraving. Each button has a backlight indicator light and offers users with strong tactile feedback. Designed to fit with standard decorator wallplates, CLS Wallstation can be ganged together to meet all project needs.

The WaveLinx Wired Sensor Powerpack (FLT-SP) provides power to low voltage sensors and communicates occupancy data status to the WaveLinx Wired system. This Sensor Powerpack is ideal for open spaces that require two or more dual technology sensors.

The CORE Locate Application (TRX-LOCBAS) is an intuitive, web-based, real-time location application that allows authorized user to locate and manage their assets within their spaces. Once indoor positioning specialists use the Locate application to configure the system, users can manage assets and locate their positions in real-time. CORE Locate application and associated services are hosted on CORE Core (Pro, Enterprise and Virtual) appliances.

CORE Locate delivers real-time indoor location service and management by leveraging the CORE smart space IoT platform. It's designed to let you monitor activities by sensing the location of your assets, so staff and patients can use the data to make improvements. Among them: optimized business/production workflows, enhanced safety and heightened security.

The PRO Outdoor Fixture High / Low Mount Sensor (SWPD*) offers passive infrared (PIR) occupancy with a photocell for closed loop daylight sensing. The sensors are IP66 rated for outdoor site and indoor environments with installation heights up to 40 feet and coverage up to 5000 square feet. Easy tool-less fixture connection (Zhaga Book 18 socket) with out of the box controls functionality. Available color options: white, black and bronze.

The WaveLinx DALI Field Relay (FRS-DA) provides On/Off control and network connectivity in order to conserve energy and effectively manage the lighting system. The Field Relay uses advanced switching technology specifically designed to handle the large inrush currents and inductive loads found in lighting applications.

The CORE Mechoshades Interface (TRX-SHADES) allows specifiers to achieve a consistent design aesthetic within the space by using the WaveLinx Pro wallstations to control both shades managed by Mechoshades system and lights managed by WaveLinx system.

The WaveLinx Unmanaged Network Switch with 8 PoE+ ports (GS308PP) provides power and data from a single CAT-5 or 6 cable to devices such as WaveLinx Area Controller and WaveLinx Touchscreen.

The remote PRO Outdoor Sensor Extender / Multiplier (RSWPD) housing incorporates a WaveLinx SWPD4 and SWPD5 wireless sensor, and is available in two distinct configurations: In the first configuration (RSWPD-WE), the device acts as a Wireless Extender. It is placed in a location where no WaveLinx enabled luminaire is present, thus providing a way for the wireless system to find a node from which to hop. This is an ideal configuration for when the WaveLinx WAC is too far from the first luminaire. In the second configuration (RSWPD-CM), the device acts as a Control Multiplier to distribute the commands from the WaveLinx system solution to multiple sensorless luminaires at once.

CORE Locate delivers real-time indoor location service and management by leveraging the CORE smart space IoT platform. It's designed to let you monitor activities by sensing the location of your assets, so staff and patients can use the data to make improvements. Among them: optimized business/production workflows, enhanced safety and heightened security.

CORE OpenADR Interface (TRX-OPNADR) allows WaveLinx users to take advantage of utility company incentives by participating in ongoing Demand Response (DR) programs. The CORE OpenADR interface is able to automatically retrieve live power demand information from the utility company and automatically activate load shed profiles according to pre-configured user settings.

CORE Locate delivers real-time indoor location service and management by leveraging the CORE smart space IoT platform. It's designed to let you monitor activities by sensing the location of your assets, so staff and patients can use the data to make improvements. Among them: optimized business/production workflows, enhanced safety and heightened security.

The PRO Battery-Powered Wallstation (WB-Series) is a multi-scene, single area dimming wallstation which provides customized light level for each area. The wallstation is available in four hardware configurations with multiple engraving options including generic SCENE versions. The wallstation is easily programmed though the WaveLinx mobile application.

CORE Locate delivers real-time indoor location service and management by leveraging the CORE smart space IoT platform. It's designed to let you monitor activities by sensing the location of your assets, so staff and patients can use the data to make improvements. Among them: optimized business/production workflows, enhanced safety and heightened security.

CORE Locate delivers real-time indoor location service and management by leveraging the CORE smart space IoT platform. It's designed to let you monitor activities by sensing the location of your assets, so staff and patients can use the data to make improvements. Among them: optimized business/production workflows, enhanced safety and heightened security.

The IR Remote (ACC-P-RT) streamlines installers' or set-up technicians' processes when commissioning WaveLinx PRO-enabled or WaveLinx LITE-enabled sensors. The IR Remote allows the installer to communicate directly with the integrated sensor and send commands. Most commonly used commands for WaveLinx PRO include enabling/disabling pairing mode, reverse identification, enabling/disabling closed loop daylighting, adjusting daylight light levels and occupancy sensor sensitivity, resetting a sensor to default factory and performing more advanced functions such as assigning point guards for large zone applications. WaveLinx LITE functionality provides reverse identification functionality during provisioning.

• Bi color Red/Green LED’s • Injection-molded thermoplastic ABS housing, UL 94V-0 flame rating • Innovative, easy installation in minutes • Letters 6″ height with 3/4″ stroke • Single or double face • Universal J*box mounting pattern • 120V/277VAC dual voltage operation • Built -in 1.2V 900mAh Nickel cadmium battery for minimum 90 minutes emergency operation • Maximum 24 hours for full recharge time • Test switch and charge indicator • 0℃ to 40℃ indoor damp location listed • The battery operated emergency exit lights are the perfect solution for applications that require both an exit sign and an emergency light.

• Injection-molded thermoplastic ABS housing, UL 94V-0 flame rating • Wet location use • Innovative, easy installation in minutes • Letters 6″ height with 3/4″ stroke • Single or double face • Universal J*box mounting pattern • 120V/277VAC dual voltage operation • Built -in 3.6 V 500mAh Nickel cadmium battery for minimum 90 minutes emergency operation • Maximum 24 hours for full recharge time • Test switch and charge indicator • 0℃ to 40℃ indoor damp location listed

RS-232 Controllable Circuit Breaker Panel The SCLC series of RS-232 controlled Load Center uses motorized circuit breakers to offer a labor-saving, one-panel alternative to relay panels. The economical Load Center panels require the least wall space for tight locations and are available in 26 and 41 circuit sizes of 3 phase, 4 wire 208Y/120Vac. Load Center’s are traditional residential panels and are consequently best suited for smaller circuit breaker counts or for applications with limited wall space. The SCLC is more economical than the bigger panelboards, and is a great value for all of the features offered! Saves Space Saves redundant installation and hardware costs! Energy efficient – NO holding current or heat sinks required to maintain state – Runs cool, lasts long! Easy set-up, no on-site commissioning or factory start-up required Simple jumper system sets RS-232 addressing Individual or zone control of circuits IP / serial integration with Building Management Systems Automatic load shedding feature standard Brownout / Power outage shut-down standard Emergency override function standard on every panel.