160 manufacturers · 18,987 products

The Solitaire Impress power modules provide expanded dimming capability to Lehigh’s Solitaire Impress modular dimming system. Solitaire Impress master stations are capable of up to 800W per channel, with a maximum of 2000W at 120V while the Solitaire Impress power modules operate at 16A, 120V or 277V. In addition, these power modules provide various dimming control solutions including standard leading edge (forward phase), trailing edge (reverse-phase/ELV), 0-10V fluorescent and LED, 2, 3, and 4-wire fluorescent, and non-dim for any application. The dual 0-10V module can provide up to 2000W single zone or split on two zones for 4-wire LEDs or fluorescent fixtures.

Lehigh's DX3 dimming system builds on the foundation of the successful DX2 system offering improved performance with a 600Mhz ARM Cortex-A8 processor and dedicated three-phase dimming controller, RDM support, USB ports, Ethernet, built-in ride-thru circuit, and a capacitive touch user interface for system configuration.

The Passive Infrared Single Level Vacancy Sensing Wall Switch is a motion sensing lighting control and conventional wall switch all-in-one that is used to for energy savings and convenience. The VNW-P-1001-MV uses Passive Infrared (PIR) sensor technology to monitor a room for occupancy and deliver maximum energy savings. The lights are turned ON by pressing the universally recognized light icon pushbutton. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application.

The Ethernet Interface Module (EIM) provides secure serial-to-ethernet data transmission to enable data exchange between Keeper Enterprise, Greengate programming software application, and the Greengate panels. The device supports the SSL and SSH protocols, which work by encrypting data before sending it over the ethernet network.

The Dual Technology Dual Relay Occupancy Sensing Wall Switch is a motion sensing lighting control and conventional wall switch all-in-one that is used for energy savings and convenience. The unit contains two relays that allow the control of two separate loads. The ONW-D-1001-DMV-N combines Ultrasonic (US) and Passive Infrared (PIR)sensor technologies to monitor a room for occupancy to deliver maximum energy savings and ensure the greatest sensitivity and coverage for tough applications without the threat of false triggers. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application. The EcoMeter provides a visual indicator of energy usage, increasing end user awareness and reminding individuals to take control of their lighting to maximize energy savings.

Available in both a network and stand-alone architecture, Room Controller offers code-compliant lighting, emergency, and plug load control out-of-the-box when connected to Room Controller low voltage devices. The system includes three relays and up to three 0-10 VDC dimming outputs to control compatible dimmable ballasts. Network up to 254 ControlKeeper and Room Controller Network panels.

Dual Relay Switchpacks provide 24 VDC operating voltage to all low voltage, 24 VDC, Greengate occupancy sensors and day lighting controllers. These powerpacks can be used where two circuits need to be controlled at the same point. A single switchpack can provide power for up to five sensors. Up to ten switchpacks can be connected to one sensor for control of multiple circuits. Isolated contacts may also be used to control HVAC, contactors, motors, etc.

The TracKeeper™ current limiting panel for track lighting allows designers to easily meet energy codes. Limiting the branch circuit volt-ampere rating with the TracKeeper™ provides you with a fixed power consumption limit for your installation as opposed to calculated values based on watts per linear foot of track. Additionally, the use of high efficiency luminaries will often yield a lower watts/linear foot number than is specified in the code. Available in either 16 or 32 circuit panels.

The Passive Infrared Low Voltage Occupancy Sensing Wall/Corner sensor is a motion sensing lighting control that is used for energy savings and convenience. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application. Manual On feature for use with 1 or 2 momentary switches controlling 1 or more Switchpacks.

The Passive Infrared Dual Relay Occupancy Sensing Wall Switch is a motion sensing lighting control and conventional wall switch all-in-one that is used for energy savings and convenience. The unit contains two relays that allow the control of two separate loads. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application. The EcoMeter provides a visual indicator of energy usage, increasing end user awareness and reminding individuals to take control of their lighting to maximize energy savings.

The External Power Supply is a system accessory for the Greengate Lighting Control System. It is used to power user interfaces and other accessories when additional power is needed.

The OSW-P-1001-MV Passive Infrared Single Level Occupancy Sensing Wall Switch is a motion sensing lighting control and conventional Wall Switch all-in-one that is used to for energy savings and convenience. PIR sensors are considered line-of-sight sensors, meaning that the sensor must be able to have a direct line-of-sight to the person making the motion. In Automatic On Mode, the lights turn ON when a person enters the room. In Manual On Mode, the lights are turned ON by pressing the Pushbutton. The sensor provides true multi-way ON/OFF control. When lights have been activated, the lights will remain on as long as one of the sensor(s) continue to detect motion. The occupant may manually turn OFF the lighting by pressing the ON/OFF button on any of the connected devices. If the room becomes vacant and the lights are ON, the lights will turn OFF when the unit that detected motion last times-out. Works with Incandescent, LED, Fluorescent, CFL, MLV, ELV or 1/2 HP motor load.

The Dual Technology Single Level Occupancy Sensing Wall Switch is a motion sensing lighting control and conventional wall switch all-in-one that is used to for energy savings and convenience. The ONW-D-1001-MV-N combines Ultrasonic and Passive Infrared (PIR) sensor technologies to monitor a room for occupancy to deliver maximum energy savings and ensure the greatest sensitivity and coverage for tough applications without the threat of false triggers. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application. The EcoMeter provides a visual indicator of energy usage, increasing end user awareness and reminding individuals to take control of their lighting to maximize energy savings.

Listed for emergency lighting control applications, the RRU-X-UNV can simultaneously bypass both a line voltage switch and a 0-10V dimming signal, ensuring that emergency fixtures illuminate at full brightness during utility power interruptions. Its small size makes it ideal for junction box or integrated fixture mounting in wireless or other modern control systems. An integral test switch allows for quick testing and verification.

The passive infrared Extreme Temperature Sensor provides consistent, stable coverage where extreme heat, cold or humidity must be accommodated, and where there are wide fluctuations in temperature. Temperature compensating circuitry stabilizes sensitivity at temperatures –40°F to 125°F (-40°C to 52°C). Ambient light control circuit to avoid False ON/OFF from brief changes in background light. Lighting sweep function with selectable DIP Switch prevents unnecessary “lights ON” following power sweeps in facilities with computer control systems

The MicroSet Ultrasonic Low Voltage Occupancy Sensing Ceiling Sensor is a motion sensing lighting control that is used for energy savings and convenience. The ultrasonic sensor uses the Doppler principle. It produces a low intensity, inaudible sound and detects changes in sound waves caused by motion, such as walking into the room, reaching for the telephone, or turning in a chair. They are volumetric in nature and therefore not line-of-sight dependent. Since they fill the space with these sound waves, they are excellent in bathrooms with stalls, enclosed hallways, or other oddly shaped rooms. In addition, they are much more sensitive to smaller motions. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and Time Delay in real-time, maximizing the potential energy savings that are available in the particular application.

The Dual Technology Dual Relay Occupancy Sensing Wall Switch is a motion sensing lighting control and conventional wall switch all-in-one that is used for energy savings and convenience. The unit contains two relays that allow the control of two separate loads. It does not require a neutral wire for installation making it ideal for retrofit applications. The ONW-D-1001-DMV combines Ultrasonic (US) and Passive Infrared (PIR)sensor technologies to monitor a room for occupancy to deliver maximum energy savings and ensure the greatest sensitivity and coverage for tough applications without the threat of false triggers. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application.

The Passive Infrared (PIR) Single Relay Vacancy Sensing Wall Switch with Night Light is a lighting control and wall switch all-in-one that is used for energy savings and convenience. VNLW-P-1001-MV-N is designed to detect motion from a heat-emitting source (such as a person entering a room) within its field-of-view and automatically switch lights ON. The night light activates when the sensor turns the lights OFF. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application.

The Passive Infrared Low Voltage Occupancy Sensing Wall Switch is a motion sensing lighting control and that is used for energy savings and convenience. The wall switch that utilizes an isolated Form-C relay that integrates directly with lighting control, building, and HVAC systems. The ONW-P-1001-SP is designed to detect motion from a heat-emitting source (such as a person entering a room) within its field-of-view and automatically switch lights ON. These sensors have multi-segmented lenses. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real time, maximizing the potential energy savings that are available in the particular application. The EcoMeter provides a visual indicator of energy usage, increasing end user awareness and reminding individuals to take control of their lighting to maximize energy savings. HVAC mode allows the load connected to the Form C BAS relay to remain ON when the lights are turned OFF manually.

The MicroSet Passive Infrared Low Voltage Occupancy Sensing Ceiling Sensor is a motion sensing lighting control that is used for energy savings and convenience. The sensor is designed to detect motion from a heat-emitting source (such as a person entering a room) within its field-of-view and automatically switch lights ON. These sensors have multi-segmented lenses. For units to sense motion, the person must cross between two segments. PIR sensors are considered line-of sight sensors, meaning that the sensor must be able to have a direct line-of-sight to the person making the motion. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and Time Delay in real-time, maximizing the potential energy savings that are available in the particular application.

The Forward Power Dimmers are system accessories for Cooper lighting control systems. It allows dimming control of 2 or 3-wire loads via 0-10V control signals. Each module includes a backbox, heatsink, temperature sensor to monitor operating temperature.

The Heavy Duty Switchpack provides 15 VDC operating voltage to all low voltage, 15 VDC, occupancy sensors and daylighting controllers. A single powerpack can provide power for up to five sensors. Up to ten switchpacks can be connected to one sensor for control of multiple circuits. Isolated contacts may also be used to control HVAC, contactors, motors, etc.

The Dual Technology Single Level Occupancy Sensing Wall Switch is a motion sensing lighting control and conventional wall switch all-in-one that is used to for energy savings and convenience. It does not require a neutral wire for installation making it ideal for retrofit applications. The ONW-D-1001-MV combines Ultrasonic (US) and Passive Infrared (PIR)sensor technologies to monitor a room for occupancy to deliver maximum energy savings and ensure the greatest sensitivity and coverage for tough applications without the threat of false triggers. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application.

The EISSBox™ is a Virtual End Node (VEN) device installed at the customer site and receives secure OpenADR 2.0 web services from the Utility and provides a signal to the lighting control system.

Linear Dimming Control Module Plenum Rated (LDCM-PL) takes a 0-10V dimming signal and converts it to an ELV dimmed output for up to 1000W with a 277V load and 450W on a 120V load. The LDCM-PL is rated to directly mount to a junction box in a plenum space for easier installations and to meet building requirements.

The VSW-P-0801-120 Passive Infrared Single or Multi-way Vacancy Sensing Wall Switch is a motion sensing lighting control and conventional Wall Switch all-in-one that is used to for energy savings and convenience. The VSW-P-0801-120 is designed to detect motion from a heat-emitting source (such as a person entering a room) within its field-of-view and automatically switch lights ON. PIR sensors are considered line-of-sight sensors, meaning that the sensor must be able to have a direct line-of-sight to the person making the motion. The lights are turned ON by pressing the Pushbutton. The sensor provides true multi-way ON/OFF control. When lights have been activated, the lights will remain on as long as on the sensor(s) continue to detect motion. The occupant may manually turn OFF the lighting by pressing the ON/OFF button on any of the connected devices. If the room becomes vacant and the lights are ON, the lights will turn OFF when the unit that detected motion last times-out. Works with incandescent, LED, fluorescent, CFL, MLV, ELV or 1/6 HP motor load.

The Field Relay provides On/Off control and network connectivity in order to conserve energy and effectively manage the lighting system. The Field Relay uses advanced switching technology specifically designed to handle the large inrush currents and inductive loads found in lighting applications.

The LightLEEDer controller is the key to a powerful, dependable, flexible and energy efficient lighting system. LightLEEDer panels come with our new Reliant40 relays which feature a superior four contact design -- the first true 40Amp lighting relay. Reliant40 relays come in 1-, 2- and 3-pole configurations in a robust breaker-style body. LightLEEDer panels range in size from 4 to 64 relay capacity and are equipped with CAT-5 RJ45 connectors for LightSync data line devices and interconnecting panels. Panels include a keyboard and LCD screen, along with USB and TCP/IP connections for easy programming with our free LightLEEDer Pro Software. Add-on modules are available for connecting to BAS, theatrical, or security systems.

The Intelligent Lighting Controls line voltage wall switch & 0-10 volt dimmer provides a stylish solution for spaces where manual dimming control is required. Designed with contractors in mind, the unit is significantly shallower than typical dimmers, resulting in less crowded wall boxes. Additionally, versatile wiring enables usage with or without a neutral connection. For dimming adjustment, intuitive raise and lower buttons are present in addition to the on/off button. Five vertically stacked LEDs are provided to indicate the current dimming level. Configurable dimming parameters include High/Low Trims, Turn on Levels, and Curve Types. This dimmer also matches the ILC family of wall switch occupancy sensors and 0-10V dimming wall switch sensors.

The Apprentice 3 programmable lighting control panel is an energy saving lighting controller. You can network up to 48 control points and 64 LightSync™ devices per network and connect via easy to use RJ-45 ports. Connect and program panels using a USB port on a laptop and our free Apprentice 3 software. Add-on cards are easy to install and and add the following capabilities: BACnet, LonWorks, N2, MODBUS, TCP/IP, or modem interface, DMX control and DTMF telephone switching. Also optional remote mount 0-10V isolated dimming control modulesforstandard daylight harvesting operations.

A LightLEEDer-24, -40, or -48 MicroLite Retrofit Insert can take your present outdated or failing MicroLite lighting control system and get it up to todays standards. All of the enhanced features of the LightLEEDer system will be available with this retrofit system from LightSync switches to BAS control. Upgrades are as simple as removing the existing hardware and replacing it with the LightLEEDer hardware provided on a single back plate insert. Reuse existing enclosure, conduit, and wiring. The LightLEEDer programmable lighting controller retrofit insert provides a dependable, flexible, and energy savings controller featuring the robust Reliant40 relay.

INTELLIGENT LIGHTING CONTROLS power pack controllers transform incoming line voltage power to Class 2 low voltage as needed by sensors or other control devices. Additionally, they switch on/off power to the connected lighting load as directed by the sensors and controls. INTELLIGENT LIGHTING CONTROLS power packs utilize a powerful microprocessor to optimize its switching timing in order to ensure long relay life even when controlling high-inrush LEDs and ballast loads. As with all INTELLIGENT LIGHTING CONTROLS products, these power packs are easy to install and incorporate features which reduce contractor labor time. An elongated chase nipple with snaps for quick installation and an optional snap-on low voltage wire chamber make for a hassle free contractor experience. All INTELLIGENT LIGHTING CONTROLS products are proudly made in the USA.

Intelligent Lighting Controls wireless power pack controllers switch on/off power to a connected lighting load as directed by wirelessly linked sensors, photocells, and wall controls. Additionally, the unit’s 0-10V dimming option greatly simplifies applications where dimming control from multiple switch locations is required. For applications where a hybrid wireless/wired architecture is desired, this wireless power pack can also be ordered with auxiliary low voltage connections.

The ILC Current Limiting Subpanel gives you the ability to limit current on lighting circuits. This gives you the ability to control the calculated load to comply with energy codes like California’s Title 24 that limit the VA (wattage). This subpanel is designed to be installed between the lighting branch circuit breaker and the lighting. These panels are custom configured with 1 to 21 breakers ranging from .5 to 16 Amps.

The LightLEEDer programmable lighting control relay panel is the key to a powerful, dependable, flexible and energy efficient lighting system. LightLEEDer panels come with our new Reliant40 relays which feature a superior four contact design—the first true 40Amp lighting relay. Reliant40 relays come in 1-, 2- and 3-pole configurations in a robust breaker-style body. LightLEEDer panels range in size from 4 to 64 relay capacity and are equipped with CAT-5 RJ45 connectors for LightSync data line devices and interconnecting panels. Panels include a keyboard and LCD screen, along with USB and TCP/IP connections for easy programming with our free LightLEEDer Pro Software. Add-on modules are available for connecting to BAS, theatrical, or security systems.

The LightSync Occupancy Sensor 8 Input module is designed to power and receive signals from multiple sensors on each of its 8 independent inputs. Eliminate expensive power packs by simply direct- wiring the sensors into the inputs. This module mounts remotely in a location central to the sensors. Each independent input can control any relay(s), group(s), or preset(s) throughout the network.

The LightSync Digital Power Supply Repeater 4 (LSPSR4) is a remote mounted power supply and data repeater. The PSR4 adds power for LightSync devices and refreshes both LS and LL data communications and is ideal for network distribution. The LSPSR4 has one input and two branch outputs with 2 ports for going up to 4 directions. The power supply supports an additional 20 LS devices and the repeaters refresh data for up to 31 more LL/LS device per branch.

The LightSync EVO Integrated 2 Room Controller has 2 isolated relays with 0-10V dimming. This controller integrates the control options of an EVO-RC with two on-board relays in one package for easy installation. Up to 3 LSEVO-INT-2-RC room cantrollers can be added to a LLEVO-INT-2 to extend its control into additional rooms or a small office with two zones of lighting control with daylight harvesting or one lighting zone and a plug load. It has RJ-45 ports for local digital LightSync switches, occupancy sensors, and a photo sensor. This convenient and easy to install two relay room controller is great for extending the controls of an LLEVO-INT-2 controller.

The LightSync DIgital device hub provides device installation using a home run configuration where the data lines are pulled directly from the devices to a single location. The hub has 20 ports that supplies power for the devices along with renewed data communications. Each port can run up to 1500 feet to devices. The hub is supplied in a NEMA 1 enclosure with a multi-tap transformer and a high voltage divider.

SENSORWORX line voltage wide view and hallway occupancy sensors are self-contained lighting control solutions that mount to the wall, corner, or ceiling. Using an adjustable angled bracket and multi-position chase nipple, these sensors reduce contractor installation time and provide a secure and clean finished appearance. SENSORWORX products utilize the latest passive infrared technology and digital signal processing techniques to provide unmatched detection performance. Additionally, these SENSORWORX units are available with an integrated microphone to provide overlapping passive acoustic occupancy detection for rooms with obstructions or where occupant motion will be limited.

The SENSORWORX family of wall switch occupancy/vacancy sensors provides a simple yet cost-effective lighting control solution for many retrofit applications. Designed with contractors in mind, the SENSORWORX 0-10V dimming wall switch sensor is significantly shallower than typical dimmers and sensors, resulting in less crowed wall boxes. Additionally, versatile wiring enables usage with or without a neutral and allows reversal of line and load connections. SENSORWORX products utilize the latest passive infrared technology and digital signal processing techniques to provide unmatched motion detection performance. These units are also available with an integrated microphone to provide overlapping passive acoustic occupancy detection for rooms with obstructions or where occupant motion is limited. For dimming adjustment, intuitive raise and lower buttons are present in a addition to an on/off button.

The SENSORWORX family of wall switch occupancy sensors provides a simple yet cost-effective lighting control solution for many retrofit applications. Designed with contractors in mind, the SENSORWORX wall switch sensor is significantly shallower than typical sensors, resulting in less crowded wall boxes. Additionally, versatile wiring enables usage with or without a neutral and allows reversal of line and load connections. SENSORWORX products utilize the latest passive infrared technology and digital signal processing techniques to provide unmatched motion detection performance. These units are also available with an integrated microphone to provide overlapping passive acoustic occupancy detection for rooms with obstructions or where occupant motion is limited.

The WaveLinx Touchscreen Wall Controller (TSC-E-7) provides an elegant and discreet light control for any WaveLinx controlled space. The portrait-oriented 7” [17.8cm] touchscreen features a low-profile design with edge-to-edge glass and an extremely responsive display making it a great architectural addition to conference rooms, executive offices and open spaces.

The WaveLinx PRO Contact Closure Input Module (CCI-P-V) provides analog devices with an interface and network addressability. It offers two modes : mode one has four inputs for momentary and sustained contact inputs . In the second mode the first channel on the device provides an input to the occupancy sensor. The CCI module communicates with other devices on the network and can easily be managed via the WaveLinx mobile app.

Easily adjustable compact digital ceiling sensor that excels due to its ability to utilize an industry leading mobile app to provision and troubleshoot. The mobile app allows contractors and technicians cut onsite time through an intuitive interface that provides active sensor feedback and provisioning flexibility. The device’s slim form factor provides a sleek aesthetic that blend into the ceiling maintaining the spaces visually appeal.

The WaveLinx LITE Emergency Switchpack (ESP-L-010-347) is a lighting control device designed to control (on/off/dim) commercial and industrial lights while providing Emergency capabilities without additional hardware. The switchpack consists of a 120-347VAC 20A relay and a continuous 0-10V dimming control. It integrates into the LITE system by forming a mesh network while communicating with other LITE devices using Bluetooth protocol. Forming a Wireless Emergency allows for other devices to communicate to the ESP, providing power loss detection.

The WaveLinx PRO Emergency Switchpack (ESP-P-010-347) is a lighting control device designed to control (on/off/dim) commercial and industrial lights while providing Emergency capabilities without additional hardware. The ESP consists of a 120-347VAC 20A relay and a continuous 0-10V dimming control. It integrates and communicates with other PRO devices and the WaveLinx Area Controller using the PRO protocol, a 2.4GHz wireless mesh network based on the IEEE 802.15.4 standard. Forming a Wireless Emergency set allows other devices to communicate with the ESP, providing power loss detection.

The CORE Lighting Application (TRX-LGT250) is an intuitive, web-based application that allows facility managers to remotely perform high-level lighting supervisory management tasks, with the power to configure and monitor their WaveLinx connected lighting system. CORE Lighting is hosted on CORE Core (Pro, Enterprise and Virtual) appliances.

CORE BACnet/IP (TRX-BACNET) Interface enables the integration of the WaveLinx Connected Lighting System with BACnet-compatible Building Automation Systems (BAS). BACnet is a data communication protocol for building automation and control networks developed by the American Society of Heating Refrigeration and Air Conditioning Engineers (ASHRAE).

The WaveLinx Wired Digital to Analog Converter (DAC-DC1 / DAC-DC2) is a lighting control device used to control any standard 0-10V current sourcing dimmable ballast/driver. It allows dimming control by sending 0-10V dimming and on/off commands to the DAC via the Cooper Lighting two wire communications bus.

The WaveLinx PRO Universal Voltage Dimming Switchpack (RSP-P-010-347) is a lighting control device designed to control (on/off/dim) commercial and industrial lights as well as receptacles. The RSP-P consists of a 120-347VAC 20A relay and a continuous 0-10V dimming control. This powerpack is an integral part of the WaveLinx system. It communicates with other PRO devices and WaveLinx Area Controller using PRO protocol, a 2.4GHz wireless mesh network based on IEEE 802.15.4 standard.

The WaveLinx Wired External Network Aux Power Supply (EXPS-15V) is a system accessory for the WaveLinx Wired Lighting Control System. It is used to power user interfaces and other accessories when additional power is needed. If there are more than 10 wall stations and/or cable runs are greater than 1,000 feet, an External Power Supply is to be used. Each External Power Supply is capable of extending the cable run an additional 1,000 feet, or 10 wall stations.

The WaveLinx Wired DIN Rail System Integrator (SI-2-D-NA) converter for interfacing with third-party devices to and from the WaveLinx Wired network. The SI-2-D enables control of a wide range of equipments and systems such as: audio systems, TVs, projectors, shades, security & fire alarms systems and Building Management Systems.

The WaveLinx Wired Touchscreen Interface (TSI-1-NA) is a module which allows the TSE Touchscreen to connect to the WaveLinx Wired Panel system. With it's integrated timeclock, it can also be used a standalone device to run schedules. The TSI-1 must be installed in a DIN rail enclosure.

The WaveLinx Wired Network Communication Cable (LCCP / LCCNP) is used to interconnect Source Controllers and peripheral devices. The cable provides one 18AWG wire pair to deliver power to peripherals and one 22AWG twisted and shielded wire pair to carry data transmissions. Both non-plenum (LCCNP) and plenum rated (LCCP) versions are available.

CORE Public REST API (TRX-API) provides a secure programming interface that enables third-party partners to obtain real-time data from WaveLinx controlled spaces as well as Cooper Lighting Solutions BLE tags. Partners can then use the data to offer value-added solutions that improve business processes and tenant experiences. The CORE Public API interface is hosted on the CORE Core appliances.

The WaveLinx Wired iCANnet to PC Interface (SW-3-NA) provides an interface between an WaveLinx Wired network and a computer running WaveLinx Wired configuration software. This compact versatile unit can be mounted virtually anywhere. The SW-3 includes a PC-NODE, Network Connection Card, phone style connection cable.

The WaveLinx Wired Universal Interface Module - Mini (UIM-NA) is a network powered universal interface with six configurable inputs. It can be dry contact closure for scene selection. 1.7" diameter potted PCB with 8" flying leads, designed to fit standard junction boxes and ideal for connection to push buttons, dry contact switches and rocker switches. Does not include LED feedback status indicators.

The WaveLinx Wired Field Relay (FRS-DA) provides On/Off control and network connectivity in order to conserve energy and effectively manage the lighting system. The Field Relay uses advanced switching technology specifically designed to handle the large inrush currents and inductive loads found in lighting applications.

The WaveLinx Wired Universal Source Controller, Feed Through (SC-UN-FT) lighting control panel provides feed-through wiring flexibility for both new and existing applications. Each Source Controller contains individual control cards that are the industry’s only “true universal” by controlling every load type without interface or multiple cards. In addition, each panel has on board Ethernet, A/V interface, Contact Closure, DMX, voltage sensing, and real-time individual dimmer power metering. Constant live feed per dimmer, for battery powered emergency lighting.