160 manufacturers · 18,987 products

DALS understands the benefits of offering a complete lighting system and solution. Our range of accessories is fully compatible with each of our LED products.

DALS understands the benefits of offering a complete lighting system and solution. Our range of accessories is fully compatible with each of our LED products.

Feeds power to Industrial HID and fluorescent lighting fixtures wired with Drop SO cords (DS) or Drop cables (DC). Provides circuit selection at each fixture and allows fixtures to be disconnected without interrupting power downstream. All unused outlets require a MWS dust cover.

Supplies power to out-of-system units that are wall-mounted or ceiling-mounted. MWS Drop cables may be plugged into the last component, Splitter (SP) or Circuit T (CT) anywhere within the system.

MWS, Modular Wiring Systems, provides low cost installation of circuit wiring for lighting and power. Using modular components that plug together, MWS can be installed in a fraction of the time of hardwiring. Plus, MWS offers the advantage of relocating fixtures and outlets for future renovations.The MWS Drop Cable with DALI Control (DC-5LT) feeds power and control to wall or ceiling fixtures from a compatible Circuit T (CT) or Splitter (SP). See the CT or SP specification sheets for compatibility details.

Used to feed Industrial HID and fluorescent lighting fixtures in open ceiling construction from a Circuit T (CT) or Splitter(SP). Fixtures wired with MWS Drop SO Cords can be disconnected under load for repair or relocation without interrupting power down line.

MWS, Modular Wiring Systems, provides low cost installation of circuit wiring for lighting and power. Using modular components that plug together, MWS can be installed in a fraction of the time of hardwiring. Plus, MWS offers the advantage of relocating fixtures and outlets for future renovations. The MWS Drop SO Cord with DALI Control (DS-5LT) is used to feed power and control wiring to suspended industrial LED and Fluorescent lighting fixtures from a compatible five-conductor Circuit T (CT). See the CT specification sheet for details on compatibility. Fixtures wired with MWS DS-5LT can be unplugged under load without interrupting power or control to downstream fixtures.

Continues the system between MWS components that interface with light fixtures, switches and convenience power outlets. Any MWS cable component may have length added with an Extender Cable. All unused outlets require a MWS dust cover.

The MWS Fitting Cable (FC) continues power from the Starter or switch drop to the first lighting fixture and between lighting fixtures. The line side connector snaps into any 1/2" knockout and has 6" #18 leads to connect to fixture wiring. MWS Fixture Cables may have length added with an Extender Cable. All unused outlets require a MWS dust cover.

Feeds Industrial HID and Fluorescent lighting fixtures in open ceiling structure while allowing the circuit to feed through to the nest fixture. All unused outlets require a MWS dust cover.

The MWS Fixture Fitting (FF) or Power Fitting (PF) feeds power to lighting fixture while allowing the circuit to feed through to the next fixture. Tap leads on FF are 18ga, tap leads on PF are 12ga.

MWS, Modular Wiring Systems, provides low cost installation of circuit wiring for lighting and power. Using modular components that plug together, MWS can be installed in a fraction of the time of hardwiring. Plus, MWS offers the advantage of relocating fixtures and outlets for future renovations. The MWS Fixture Fitting with DALI Control (FF-5LT) feeds power and control to any lighting fixture, while allowing the power and control to feed through to the next fixture

The MWS Starter Fixture Cable (SF) starts the MWS system immediately at the electrical junction box or at the switch box and continues to the first lighting fixture. Subsequent fixtures connected to the Starter Fixture Cable are wired with standard Fixture Cables(FC). The line side connector installs into any 1/2" knockout and has #18 tap leads to connect to the fixture wiring. All unused outlets require a MWS dust cover.

MWS, Modular Wiring Systems, provides low cost installation of circuit wiring for lighting and power. Using modular components that plug together, MWS can be installed in a fraction of the time of hardwiring. Plus, MWS offers the advantage of relocating fixtures and outlets for future renovations. The MWS T Cable with DALI Control (TC-5LT) feeds power and control wiring to wall or ceiling fixtures while feeding downstream to another fixture. Compatible MWS Extender Cables (EC) are used connect either end of the TC-5LT. See the Extender Cable specification sheet for compatible models.

Feeds power to wall mounted or ceiling mounted fixtures and convenience outlets while feeding circuits downstream to another electrical component. MWS Extender Cables feed power to each T Cable. All unused outlets require a MWS dust cover.

MWS, Modular Wiring Systems, provides low cost installation of circuit wiring for lighting and power. Using modular components that plug together, MWS can be installed in a fraction of the time of hardwiring. Plus, MWS offers the advantage of relocating fixtures and outlets for future renovations. The MWS T Cable with DALI Control Only (TC-PP5LT) feeds only the control wiring to wall or ceiling mounted DALI controls, while feeding both power and control downstream to another fixture. Compatible MWS Extender Cables (EC) are used connect either end of the TC-PP5LT. See the Extender Cable specification sheet for compatible models.

MWS, Modular Wiring Systems, provides low cost installation of circuit wiring for lighting and power. Using modular components that plug together, MWS can be installed in a fraction of the time of hardwiring. Plus, MWS offers the advantage of relocating fixtures and outlets for future renovations. The MWS T SO Cord with DALI Control (TS-5LT) is used to feed power and control wiring to suspended industrial LED and Fluorescent lighting fixtures from a compatible five-conductor Extender Cable (EC). See the EC specification sheet for details on compatibility.

Introduces local switching into the MWS system. Switch Drops may be installed during rough-in or renovations. Extender Cables bring power from starters to the first Switch Drop and between consecutive Switch Drops. Switch Drops can also be connected together for multiple switch locations. All unused outlets require a MWS dust cover.

The MWS Starter Fitting is the starting point for the MWS system. The Fitting is installed in a standard 1/2" knockout of an electrical unit. The Starter Fitting is mounted externally and does not impact wire fill. All unused outlets require a MWS dust cover.

MWS, Modular Wiring Systems, provides low cost installation of circuit wiring for lighting and power. Using modular components that plug together, MWS can be installed in a fraction of the time of hardwiring. Plus, MWS offers the advantage of relocating fixtures and outlets for future renovations. The MWS Starter Fitting with DALI Control (ST-5LT) is the starting point for bringing the power and control system together. Converts conventional wiring and merges control wiring into MWS. Branch circuits are fed from the panel to a junction box with conduit and wire, while control circuits are run as Class 1 to meet local codes. The MWS Starter is mounted to the junction box with a ½” threaded lock nut connector. Power and control wires are then connected to the appropriate leads of the Starter

The MWS Splitter (SP) adds an additional power out at any point within the MWS system. All unused outlets require a MWS dust cover.

The Tandem In-Line Wiring option provides factory installed wiring when fixture sections are applied in pairs, and require left/right lamp switching. To explain, ballast receive their power from the circuit, with lamps getting their power from the ballast. TILW is the method of applying power from the ballast to specific lamps. TILW only applies to 2 or more lamp cross sections. If the luminaire has only one row of lamps, TILW is already present and unnecessary to specify. The TILW option is available on IA/IC, DI/DIM/DIVM, EI/EIM/EIVM, SS, SSL, SN, SNSM, SNRA, STN, STM, STW, RCG, P410, UT, I5 and BSX. Certain airborne contaminants can diminish the integrity of acrylic components. Refer to the Material Compatibility tables for additional information.

The Plug-In System provides factory installed branch circuit wiring and plug-in connectors when row mounting fixtures. This labor and time saving option is designed to simplify fixture installation and wiring and allows fixtures to be installed quickly and easily. The PI system is available for fixture sections up to 8' in length for continuous row wiring by simply plugging the sections together. Each PI section is factory wired to the ballast leads and color coded for easy circuit identification. Standard PI system harness contains no separate groundwire, with ground provided by the fixture body. An option to the system provides a separate ground wire in the harness where required. Certain airborne contaminants can diminish the integrity of acrylic components. Refer to the Material Compatibility tables for additional information.

Lumiere offers a variety of surface, wall, and tree mounting accessories. All are equipped with a standard 0.5-inch NPS threaded mounting hole to accept fixtures with 0.5-inch NPS threaded stems.

Coronado 812 is a compact line voltage fixture for use with PAR38 halogen lamps. The fully adjustable mounting stem provides 340° tilt and 360° rotation for easy aiming. Various lenses, louvers and color or dichroic filters can be combined – up to three at once – to create multiple lighting effects.

Coronado 806 is a ultra-compact line voltage fixture for use with PAR20 halogen lamps. The fully adjustable mounting stem provides 340° tilt and 360° rotation for easy aiming. Various lenses, louvers and color or dichroic filters can be combined – up to three at once – to create multiple lighting effects.

The Lumière Eon 303 Pathway luminaires provide architectural styling with bright, energy efficient LEDs, tailored to fit your application. The minimalist, low profile design is made from machined aluminum, contains a sealed optical compartment and mounts to an integral recess junction box creating an IP66 rated fixture that will look and perform great for years. The Eon Pathway luminaire is ideal for walkway applications where mounting heights of 26 inches or less are desired and greater lateral or forward throw illumination is needed.

Set of 4 coil springs for use with 301, 310, 401 and 426 trims in the H7 recessed housing family.

Pre-terminated Control Cable, couplers and splitters connect the Room Controller or DLVP power module and devices simplifying the Click & Go connection enabling automatic functionality upon power up. Cables are pre-terminated with industry standard RJ45 connectors.